Failed lot disposition options (batch 2 guide 14)
For importers planning failed lot handling work, the conclusion is straightforward: confirm readiness and criteria in writing before the visit, verify on site against those criteria, and decide from the written evidence. This guide explains how that discipline applies to failed lot handling assignments around factory floor operations, including how sampling logic, documentation, and follow-up fit together. Readers who apply the sequence below will spend fewer visits reaching a shippable lot.
Key takeaways
- Decide the visit objective first, because failed lot handling visits answer different questions depending on whether the lot is new, borderline, or already failed.
- Behind a CE mark sits a conformity assessment route, technical documentation, and a signed declaration by the responsible party[1].
- Freeze the specification version, the defect classification, and the packing list before the inspector travels, so checking every unit stays anchored to agreed criteria.
- The familiar AQL tables come from the acceptance-sampling tradition of balancing producer and consumer risk through statistically planned samples[2].
- ISO 9000 vocabulary helps buyers and factories use the same terms for nonconformity, correction, and corrective action[3]. Keep this reference in mind when failed lot handling decisions touch regulated characteristics.
For regulated characteristics, such as restricted substances or safety functions, disposition options narrow sharply: the lot must either be brought into conformity through verified correction or held back, because paperwork alone cannot cure a substantive failure.
Sorting makes sense when defects are visible and separable, because trained sorters can remove the nonconforming units while keeping the conforming ones, and a follow-up verification confirms the separation worked.
The sections below follow the order buyers actually encounter the task, from planning through the visit to the follow-up.
What a failed result actually means
Buyers usually choose among four practical paths: sort or rework the lot and re-verify, negotiate a concession for minor issues, downgrade the goods to a less demanding channel, or reject and remake the affected portion. Behind a CE mark sits a conformity assessment route, technical documentation, and a signed declaration by the responsible party[1].
Time pressure often pushes teams toward a quick concession, yet accepting a known defect without understanding its distribution across the lot tends to move the problem to the destination warehouse, where fixing it costs far more.
After the visit, treat the findings as the starting point for supplier development rather than a one-off verdict: share the defect photographs with the factory's production supervisor, agree which workstation or material input produced each issue, and set a date for the factory to report back on the countermeasure.
Where the purchase order involves several models or assortments, confirm the breakdown before the visit day so the sample can be allocated proportionally; mixed lots checked against a single blended criterion are a frequent source of disputes that a short clarification message would have prevented.
Disposition paths buyers really use
| Cost element | What it covers | How buyers control it |
|---|---|---|
| Inspector working day | On-site checking plus the standard defect breakdown | Stage goods so the day is fully productive |
| Travel and lodging | Movement to distant sites where applicable | Group nearby sites into one trip |
| Additional headcount | Extra inspectors for large or complex lots | Freeze the quantity before booking |
| Return visit | Re-verification after sorting or rework | Make corrections specific and checkable |
| Waiting time | Idle hours when goods or documents are missing | Confirm readiness the day before |
Use the table as a pre-visit checklist: when every row has an owner and a confirmation time, the failed lot handling visit usually runs to plan. Consistency across orders matters more than perfection in any single lot, so keep the same defect classification and the same sampling logic from one shipment to the next; when the yardstick stays fixed, trends in the reports actually mean something and both sides can see whether quality is improving.
Keeping the shipment plan intact
Rework is appropriate when the defect has a defined fix, such as re-stitching, re-polishing, or replacing a component, followed by a focused re-check of the repaired characteristic rather than a full repeat of everything.
The defect breakdown from the visit is the anchor of this discussion, since it ties each defect to a criterion, a sample reference, and a photograph, which keeps the negotiation about facts rather than impressions. When dates shift, UTS reassigns the inspector so the shipment does not wait for a new booking cycle.
End the visit with a short closing discussion at the factory floor, confirming what was found and what happens next, while the evidence is still on the table.
Evidence the factory needs from you
- Confirm readinessAsk the factory to confirm finished quantity, staging, and the contact person for the visit day.
- Freeze the criteriaLock the specification version, the defect classification, and any buyer-specific checkpoints in writing.
- Run the visitDraw samples randomly, work through the checklist, and photograph each defect type with its reference.
- Decide on evidenceCompare the findings with the acceptance criteria and choose among ship, hold, sort, or rework.
- File and follow upStore the defect breakdown with the order documents and track any corrective action to closure.
How sorting and rework decisions compare
Keep the defect breakdown together with the specification and packing list, so the next order with the same supplier starts from documented facts.
Consistency across orders matters more than perfection in any single lot, so keep the same defect classification and the same sampling logic from one shipment to the next; when the yardstick stays fixed, trends in the reports actually mean something and both sides can see whether quality is improving.
Sources
- Wikipedia: CE marking —— Overview of CE marking as conformity marking for products sold in the European Economic Area.
- Wikipedia: Acceptance sampling —— Overview of acceptance sampling including AQL concepts used in product inspection.
- Wikipedia: ISO 9000 —— Overview of the ISO 9000 family of quality management standards.
Frequently asked questions
When should the visit be booked?
Book once the factory confirms the finished quantity and staging date. Booking earlier secures the slot, but the date should track real production status rather than the original plan.
How should the report be used with the supplier?
Walk through the defect pages code by code, agree the correction for each, and set the evidence expected at any return visit. Written follow-up beats verbal promises every time.
What happens if the lot fails?
The defect breakdown records which criteria were missed and how. Buyers then choose among sorting, rework with re-verification, concession for minor points, or rejection, depending on the defect type and distribution.
How are defects classified?
Critical, major, and minor categories tied to the specification and, where relevant, safety or regulatory characteristics. Agreeing the classification before the visit prevents most on-site disagreement.
Shop 12,400+ vet-authorized medicines.
From flea & tick preventives to compounded cat thyroid chews — reviewed by a DVM, priced 31% below clinic retail on average.
This article is for educational purposes only and does not replace veterinary care. Always consult your licensed veterinarian before starting, changing, or stopping any medication or supplement for your pet.